Work Completed on Baggywrinkle
since August 1999
- Replaced Plexiglas windows
in main cabin with Lexan
- Replaced broken glass with
new glass in two portholes
- Put dog latches on forward
hatch
- Put Adjustment arm on forward
hatch
- New bolt lock on pull out
berth
- Painted inside and tops
of cabinets
- Painted sail lockers and
lazarette
- Installed wooden partitions
in sail lockers
- Replaced cockpit drain hoses
- Mounted horse shoe float
and xenon safety light
- Tapped shroud boots to spreaders
- Ran wire to compass light
- Replaced fuel fill line
- Repaired running lights
- Put tube from windless chain
drop to anchor locker
- Painted peg board over shelves
- Plexiglas over engine controls
- Painted capstan
- Added Stainless Steel protection
grab bar to capstan
- Secured compass
- Float switch on bilge pump
- Auto/manual switch on bilge
pump
- New fresh water pump
- Foot pump for fresh water
installed
- Foot pump and faucet from
salt water installed
- New faucet for pressure
fresh water
- Converted stove to propane
- Rebuilt and painted head
toilet
- Installed new hose and new
vented loop for head
- Installed two new through
hulls for head (plastic ball valve)
- Painted head and oiled wood
- New light fixture for head
- New mirror for head
- Installed hooks for towels
- Installed new pressure water
lines to head (hot and cold)
- Installed new head fresh
water faucet
- Replaced drain hose and
through hull (plastic ball valve)
- Installed sump pump for
head with vented loop and auto/manual switch
- Replaced Battery
cables with larger gage wire
- Rewired engine controls,
and Starter motor on engine
- Moved fuel filter and fuel
pump to other side of engine compartment
- Had starter rebuilt (new
solenoid)
- Replaced heat exchanger
(after it went)
- Removed glow plugs, tested,
rewired and replaced (forward one broken but still works)
- Replaced Alternator with
new one
- Replaced Secondary fuel
Filter bracket (bleed screw housing broken)
- Installed squeeze bulb in
fuel line
- Removed old blower for Gas
engine
- Made V-berth inset
- Repainted cowl vents
- Replaced folding step in
v-berth
- Removed old ice box
- Installed insulation in
pot locker to make new icebox in galley. Glassed and painted box, drip
hose to bilge
- Had new cushions made
- Had new dodger made
- Had new cover for windless
made
- New carpet for floor
- Had table made adjustable
with new pedestal
- Had gimbals for stove made
- Made new handrails inside
and out, varnished and installed them
- Installed new fire extinguishers
two
- New screens for port lights
- New wood for companionway
- Teak handles for companionway
- New hatch boards with one
being Plexiglas
- Installed AM/FM radio with
6 CD changer
- Installed cockpit speakers
- Installed cabin speakers
- New fuse panel and electrical
wiring
- Heart battery monitor installed
- Installed fathometer transducer
- Painted bottom of boat
- Installed Zink on prop
- Cut close cell foam for
cockpit cushions
- Removed and repaired water
tank!!!
- Rebuilt Aires wind vane
self steering
- Repacked windless with grease,
and reseated it on deck
- Built foldable cover for
stove
- Built glass holder for galley
- Propane tank secured with
seat on stern of boat
- Built ratlines and belaying
pins
- Installed Manual Bilge pump
- Had Diesel tank cleaned
- Installed jiffy reefing
system
- Installed track stop under
gooseneck
- Replaced electric bilge
pump
- Two new cowl vents for house
- Painted deck with nonskid
(Kingston gray)
- Installed Galley Strap
- Sanded and Varnished wood
on deck
|
